1A Static Vertical, 1B Static Boom, 3A Mobile Vertical & 3B Mobile Boom

Course Syllabus

Duration:      1 day

Ratio:             4 Operators:              1 Instructor    :           1 Machine

Course Aim:

To teach potential operators’ relevant theoretical knowledge and practical skills to safely operate a MEWP to recognised industry standards.

Course Expected Outcomes:

By the end of the course successful candidates should:-

  • Have retained the required knowledge to be able to pass the associated knowledge test
  • Be able to efficiently inspect the machine and pass the pre-use check test
  • Have demonstrated relevant skills to be able to pass the basic skills test

Course Elements:

The course will comprise of theoretical and practical instruction covering the following:-

  • Course registration / outline
  • The need and reasons to train
  • Responsibilities under the Health & Safety at Work Act 1974, PUWER 98 and LOLER 98
  • Working at Height Regulations, including the hierarchy of control
  • Avoiding danger from overhead power lines (GS6)
  • Working alone (employer and employee responsibilities)
  • Safety signs and signaling
  • Selection and use of personal safety equipment
  • Safe operating practices
  • Introduction to the machine including recommended mount and dismount, motive and steering controls
  • Starting and stopping-emergency stops
  • Basic steering exercises open area
  • Advanced steering exercises restricted area
  • Rated capacity
  • Factors affecting stability
  • Working near water
  • Working on / traveling on the public highway
  • Daily and weekly maintenance schedules
  • Planning of work including risk assessment and rescue plans
  • The hydraulic system
  • Pre use checks including the use and testing of safety devices, limit switches and hydraulic functions
  • Emergency lowering procedures
  • Correctly position, set up the MEWP and elevate to set targets at various heights
  • Where applicable, manoeuvre and operate the MEWP (3A and 3B) elevated, safely and efficiently, using mobile controls
  • Park and shut down the MEWP correctly in a pre-determined position
  • Correctly stow away work equipment
  • Operate to banks person / signaller instructions
  • Operate safety on the public highway (maybe simulated)
  • Preform battery maintenance, charging procedures or refueling operations safely
  • Preform a post stop inspection
  • Associated knowledge, pre use check and practical basic skills test
  • Feedback and course closure

Knowledge:

On completion of training candidates should have gained a theoretical understanding of the following:-

  • The need and reasons to train
  • Responsibilities under the Health & Safety at Work Act 1974, PUWER 98 and LOLER 98
  • Working at Height Regulations including hierarchy control
  • Avoiding danger from overhead power lines (GS6)
  • Working alone (employer and employee responsibilities)
  • Safety signs and signaling
  • Selection and use of personal safety equipment
  • Safe operator practices
  • Rated capacity
  • Factors affecting stability
  • Working near water
  • Working on / traveling on the public highway
  • Daily and weekly maintenance schedules
  • Planning of work including risk assessment and rescue plans
  • The hydraulic system

Skill:

On successful completion of training the candidate should be able to:-

  • Identify motive and steering controls
  • Start and stop the machine including in an emergency
  • Complete basic steering exercises open area
  • Complete advanced steering exercises restricted area
  • Perform a pre use check including the use and testing of safety devices, limit switches and hydraulic functions
  • Demonstrate correct use of emergency lowering procedures
  • Correctly position, set up the MEWP and elevate to set targets at various heights
  • Where applicable, manoeuvre and operate the MEWP (3A and 3B) elevated, safely and efficiently, using mobile controls
  • Park and shut down the MEWP correctly in a pre-determined position
  • Correctly stow away work equipment
  • Operate to banks person / signaller instructions
  • Operate safety on the public highway (may be simulated)
  • Perform battery maintenance, charging procedures or refueling operations safely
  • Perform a post stop inspection

Training and tests can be performed indoors or outdoors but where possible a combination of both would be preferred wherever possible and appropriate (careful consideration for vehicle mounted types).

Notes:

It is highly recommended that full body harness and fall restraint systems are worn wherever equipment provides specific anchoring points (this would also be encouraged for scissor lifts where such points are available). Therefore, all candidates attending must have either undertaken harness training prior to, or receive harness training that is incorporated into the MEWP course. Extended course durations will be required.

As a minimum, this coverage must include identifying anchorage points in platforms; harness standards; types of lanyard; differences between fall arrest and fall restraint; equipment inspections; correct fitting; adjustment and use of equipment; rescue procedures and current recommendations.

It is also recognised that there are many manufacturers of mobile work platforms and designs vary greatly. Any instructor carrying out training and testing must be fully conversant with the equipment type being used and make any appropriate adjustments to meet safety standards for that particular design.